estac
estac
0

Holybro Kakute F7 Controlador de Vuelo y Atlalt HV V2 40CH VTX y 65A BL_32 Tekko32 F3 Metal 4in1 65A ESC Combo para RC Drone fghfhfgjdfj

€157.84

 €88.60
Ahorre: 44% descuento

€157.84

 €88.60
Ahorre: 44% descuento

CANTIDAD

DESCRIPCIÓN DE PRODUCTOS

Brand Name: HolybroItem Name: F7 FC & 65A 4in1 ESC & 5.8G 40CH VTX Stack ComboStack Height: 26mmItem size: 35x41x7mmKakute F7 Flight ControllerItem name: Kakute F7 MCU: STM32F745 32-bit processorIMU: ICM20689 (SPI)Barometer: BMP280Dimensions: 35x41x7mm (includes foam-mounted gyro board in height)Mounting Holes: Standard 30.5mm square to center of holesWeight: 9gAtlalt HV V2 40CH VTX Item Name: 5.8G 40CH 25/200/500/800mW FPV TransmitterModel: Atlatl HV V2Transmitting Output Power: 25mW/ 200mW/ 500mW/ 800mW Switchable Audio: 6 MHz 6.5 MHz MonoAntenna Connector: MMCXInput Voltage: 7-28V (2-6S Lipo)Dimension: 35(L)x 25(W)x 7(H)mm Mounting Hole: 30.5x30.5mmWeight: 9.3gTekko32 F3 Metal 4in1 ESCModel: Tekko32F3 Metal Item Name: 65A BL_32 32Bit DShot1200 4 in 1 ESCCon. Current: 65APeak Current: 80AInput Voltage: 4-6S Lipo SupportExt. cap needed for 6s (470uf 35v for 6s usage)F3(M4 Core) MCU. Runs BLHELI32 firmware. the MCU works at 108MhzSize: 42x42mmMounting Hole: 30.5x30.5mmWeight: 12gPackage information:Package size:95*65*52mmPackage weight: 88g Ploybag packagePackage Included:1x Kakute F7 Flight Controller1x Atlalt HV V2 5.8G FPV Transmitter1x 80mm SMA--MMCX Cable1x 150mm 4pin JST GH wire 1x Tekko32 F3 Metal 4in1 ESC 1x 470uF 35V Electrolytic Capacitor1x 8pin to 8pin 1mm pitch 65mm Cable1x 8pin to 8pin 1mm pitch 25mm CableNotes:1. The air flow is very import if you want to run this 4in1 in high current.2. The input cable(from lipo to 4in1). should be good soldered. and at least 12AWG3. Please use non-metallic isolation standoffs (marked in red in the diagram above) for the mounting holes on the ESC.Because mounting holes and motor pad are connected.4.There might be some deviation due to manual measurement.
1.El 4in1 tiene un sensor de corriente analógico incorporado. y función TLM (entonces no hay lectura de corriente sobre TLM).
2.Utilizando funda metálica mosfet para una mejor disipación del calor.
3.BLheli_32 firmware. soporte Oneshot. Multishot. Dshot150. DShot300. DShot600 y DShot1200.
4.Controlador de vuelo Kakute F7 Admite receptores en serie (SBUS. iBus. Spektrum. Crossfire) únicamente. Los receptores PPM y PWM no son compatibles.
5.Controlador VCP USB del controlador de vuelo (todos los UART se pueden usar simultáneamente; el USB no ocupa un UART) 6 UARTS de hardware (UART1.2.3.4.6.7)

Ver más detalles